Ingénierie des fixations ◉ Grandes séries ◉ E-Shop

IEC

Expansion Insert - C Type: short

Insert à expansion de type C: court avec une couronne d’ancrage pour plastiques thermodurcissables et thermoplastiques - Secam Fixation

Straightforward and quick manual installation
Locking improves torque resistance and holding force
Very sharp teeth for improved penetration of material
Low cost

  • Straightforward and quick manual installation
  • Locking improves torque resistance and holding force
  • Low cost
  • Very sharp teeth for improved penetration of material

Ingénierie des fixations
Grandes Séries – E-Shop

Div 5
Div 3
Div 6
Div 4
Div 1
Div 2
Image technique 1
Image technique 2
Part Number Thread M (6H) L (mm) Ø E (mm) Ø A (mm) Ø B (mm) Well ØFiche technique 3D
IE C 020 035 T039 L 0M2 X 0.403.53.93.53.13.10
 
IE C 025 040 T044 L 0M2.5 X 0.4544.443.53.60 - 3.70
 
IE C 030 050 T056 L 0M3 X 0.5055.654.54.60 - 4.70
 
IE C 035 050 T059 L 0M3.5 x 0.6055.95.54.95.00 - 5.20
 
IE C 040 050 T066 L 0M4 X 0.7056.665.45.50 - 5.70
 
IE C 050 060 T076 L 0M5 x 0.8067.676.56.60 - 6.70
 
IE C 060 070 T086 L 0M6 X 1.0078.687.57.60 - 7.70
 
Expansion Insert – C Type: short

Phase
01

The insert is placed in a cavity which is either drilled or moulded in: the well.

Phase
02

The insert is forced into the well by axial pressure, deforming slightly in the process. The insert will be flush with the material to avoid possible removal due to lever effect.

Phase
03

As the screw goes in, the insert returns to its original shape, the locking pyramids are forced into the material, providing holding force and torque resistance. Select a screw long enough to effectively force the locking pyramids into the material. The screw must never come into contact with the bottom of the well.

  • D’après essais labo réalisés sur des matières non chargées
  • Valeurs données à titre indicatif

Produit

Sous Famille

Type

Taraudage

L

Forme Extérieure

Ø E

Matière

Spécification

Exemple

I

E

C

0

2

0

0

3

5

T

0

3

9

L

0

Insert

à Expension

Court

Taraudage intérieur
M2 (1/10 de mm)

Longueur totale 3.5 mm
(1/10 de mm)

Tréfilé

Diamètre le plus grand
3.9 mm (1/10 de mm)

Laiton CW 614N

Aucune

Sous Familles
E à Expension

Type d’insert à Surmouler
C Court
L Long

Forme extérieure
T Tréfilé
H Hexagonal

Matières
L Laiton CW 614N
A Acier trempé
1 Inox 1.4305 (A1-303)
2 Inox 1.4567 (A2-304Cu)
4 Inox 1.4404 (A4-316L)
5 Inox 1.4571 (A5-316Ti)

Spécifications
0 Aucune
1 ZnNi Zinc Nickel
N Nickelage